This forum contains outdated content and is available for reading only. Please contact technical support if you have any questions.

You specify units value that cannot be converted to pixels

Hi,

We have a code as below to "reset" the vobject angle. But, sometimes, it does crash...
and here are the error message that we get...
Mod - _PaneDesign, Proc - ResetAngle, Ln 10
5 - You specify units value that cannot be converted to pixels.(Aurigma.GraphicsMill)

May I know what can we do to prevent this?

Thanks.



    Public Sub ResetAngle()
        Const ProcedureName = "ResetAngle"
1:      Try
2:          Dim obj As Aurigma.GraphicsMill.WinControls.VObject
3:          For Each obj In _mlvMain.CurrentDesigner.VObjects
4:              If TypeOf obj Is Aurigma.GraphicsMill.WinControls.ImageVObject Then
5:                  Dim corners As System.Drawing.PointF() = GetTransformedCornerPoints(obj)
6:                  Dim angle As Single = CalcAngle(New System.Drawing.PointF(1000, 0), New System.Drawing.PointF(corners(1).X - corners(0).X, corners(1).Y - corners(0).Y))
7:                  Dim point As New PointF(obj.GetVObjectBounds.Width / 2, obj.GetVObjectBounds.Height / 2)
8:                  If angle <> 0 Then
9:                      obj.Transform.RotateAt(-angle, point)
10:                     obj.Update()
11:                 End If
12:             ElseIf TypeOf obj Is Aurigma.GraphicsMill.WinControls.TextVObject Then
13:                 Dim corners As System.Drawing.PointF() = GetTextTransformedCornerPoints(obj)
14:                 Dim angle As Single = CalcAngle(New System.Drawing.PointF(1000, 0), New System.Drawing.PointF(corners(1).X - corners(0).X, corners(1).Y - corners(0).Y))
15:                 Dim point As New PointF(obj.GetVObjectBounds.X + obj.GetVObjectBounds.Width / 2, obj.GetVObjectBounds.Y + obj.GetVObjectBounds.Height / 2)
16:                 If angle <> 0 Then
17:                     obj.Transform.RotateAt(-angle, point)
18:                     obj.Update()
19:                 End If

20:             End If
21:         Next

22:     Catch ex As Exception
23:         WriteErrLog(Err.Number, Err.Source, Err.Description, gstrModule, ProcedureName, Err.Erl)

24:     End Try
Hi Ching-Yen,

We tried to investigate your problem but we have not the code of these functions from your code:
GetTransformedCornerPoints(obj)
GetTextTransformedCornerPoints(obj)

Could you please send me the code of these functions.
Public Function GetTransformedCornerPoints(ByVal obj As Aurigma.GraphicsMill.WinControls.ImageVObject) As System.Drawing.PointF()
Const ProcedureName = "GetTransformedCornerPoints"
1: Dim baseRect As System.Drawing.RectangleF = obj.GetVObjectBounds()

2: Dim cornerPnts As System.Drawing.PointF() = New System.Drawing.PointF(3) {}

3: Try
4: cornerPnts(0) = baseRect.Location
5: cornerPnts(1) = New System.Drawing.PointF(baseRect.Right, baseRect.Top)
6: cornerPnts(2) = New System.Drawing.PointF(baseRect.Right, baseRect.Bottom)
7: cornerPnts(3) = New System.Drawing.PointF(baseRect.Left, baseRect.Bottom)

8: obj.Transform.TransformPoints(cornerPnts)

9: Catch ex As Exception
10: WriteErrLog(Err.Number, Err.Source, Err.Description, gstrModule, ProcedureName, Err.Erl)
11: Finally
12: End Try
13: Return cornerPnts
End Function

Public Function GetTextTransformedCornerPoints(ByVal obj As Aurigma.GraphicsMill.WinControls.TextVObject) As System.Drawing.PointF()
1: Dim baseRect As System.Drawing.RectangleF = obj.GetVObjectBounds()

2: Dim cornerPnts As System.Drawing.PointF() = New System.Drawing.PointF(3) {}
Const ProcedureName = "GetTextTransformedCornerPoints"
3: Try
4: cornerPnts(0) = baseRect.Location
5: cornerPnts(1) = New System.Drawing.PointF(baseRect.Right, baseRect.Top)
6: cornerPnts(2) = New System.Drawing.PointF(baseRect.Right, baseRect.Bottom)
7: cornerPnts(3) = New System.Drawing.PointF(baseRect.Left, baseRect.Bottom)

8: obj.Transform.TransformPoints(cornerPnts)

9: Catch ex As Exception
10: WriteErrLog(Err.Number, Err.Source, Err.Description, gstrModule, ProcedureName, Err.Erl)
11: Finally
12: End Try
13: Return cornerPnts
End Function

Hi,

Thanks for the code. We found the reason of your problem. Try the following code:
Private Shared Function CalcAngle( _
ByVal v0 As System.Drawing.PointF, _
ByVal v1 As System.Drawing.PointF) As Single

	Dim dotProduct As Single = v0.X * v1.X + v0.Y + v1.Y
	Dim vLengthProduct As Single = CalcLength(v0) * CalcLength(v1)

	If vLengthProduct < 0.01 Then
		Throw New ApplicationException("Ups, div by zero error...")
	End If

	'this is the fix. The argument of Acos() should be in [0, 1] interval
	Dim cosValue As Double = Math.Min(1.0F, dotProduct / vLengthProduct)
	cosValue = Math.Max(-1.0F, cosValue)

	Dim result As Single = CType(Math.Acos(cosValue) / Math.PI * 180, Single)

	Dim vecProduct As Single = v0.X * v1.Y - v0.Y * v1.X
	If vecProduct < 0 Then
		result = 360 - result
	End If

	Return result
End Function